loader-logo

LMS608

LMS608

LMS608’s powerful configuration capabilities enable rapid setup of complex and extensive touring, event and installed

Designed and proven to work uncompromisingly and continuously around the clock, it is the perfect complement to any audio installation involving passive systems. LMS processors include a wide range of factory presets for various configurations of Amate Audio passive loudspeaker systems.

Inputs4 (XLR) + 2 AES/EBU (1x XLR)
Outputs8 (XLR)
Input Level (Nominal / Max)0 dBu / +24 dBu
Input Dynamic Range> 116 dB(A)
Output Level (Nominal / Max)0 dBu / +12 dBu
Fequency Response20 Hz – 20 kHz (+/– 0.5 dB)
A/D Converters24–bit, 96 kHz
Latency< 1 ms
ConnectivityUSB & Ethernet
MainsUniversal switch mode Power Supply 90-264 V / 45-65 Hz
Dimensions (HxWxD)1U 19” Rack, 44 x 483 x 165 mm
Weight2.5 kg

Data Sheet

Download

General user’s manual

Download

DSPLink 10.0.12 for WINDOWS 32-bit version

Download

DSPLink 10.0.12 for WINDOWS 64-bit version

Download

DSPLink 10.0.12 for MacOS

Download

Frequently Asked Questions

Yes. Open DSPLink, then unlock de unit using the administrator password (Ad_min). DSPLink will let you access and edit the outputs OUT1-8. Once the desired preset is loaded, you can tune it freely. When you are done just save the customised preset in one of the free memories.

Just enter the administrator password (Ad_min) to gain access to the unit without losing all the previous work.

One of the main features of a digital signal processor (DSP) are the limiters. Using them we can guarantee that the maximum signal input in the amplifiers is below a threshold. Usually, this threshold is set just below the mechanical drive limit of the speakers, or a maximum SPL set by the application. If the threshold is set to low, the performance of the system is wasted away. If set too high, the speakers might be damaged.

For applications where all the electronics in the signal chain are our own Amate Audio systems, we developed an app with lab parameters that let us to configure the limiters so you can get 100% of system performance without compromising the safety of the loudspeakers. The application can be found in the following link: LimCal.

The required bandwidth between the LMS608 and de PC is higher than for the LMS206, for this reason we recommend using the RJ-45 Ethernet connection in a dedicated network, without a Firewall. The USB-B port of the LMS608 is present just for compatibility with legacy systems.

Although in the former years the Digital Signal Processing state of the art improved quickly, not always is a must to install a DSP. All our Amate Audio systems are launched highly calibrated after a deep R+D process that aims to easily solve the different applications of our product range. Nevertheless, using an external DSP would be necessary in the following cases:

  • Sound systems with passive speakers in applications where, due to room acoustics or type of music, corrections of the frequency response are needed (equalization)
  • Sound systems with passive speakers for touring
  • Fixed installations with different audio zones
  • Hi-Impedance installations with either speaker intelligibility or SPL requirements

If you are still not sure about getting a DSP, you can ask to our Application Engineers.

Related Products

Nítid N15P

N15P

Nítid N12WP

N12WP

HD3200

HD3200 Power Amplifiers

Nítid N12P

N12P
  • 1x D-LINK DAP-2360 Wireless Access Point + support
  • 1x Access Point power supply
  • 1x Ethernet cable, ECRJ45-1200 with housing shield both ends
  • 2x Ethernet cable, ECRJ45-500 with housing shield both ends
  • 1x Neutrik cable extension (RJ-45 feedthrough)
  • 1x USB Pendrive – with DSP Studio software

Transport aluminium briefcase included